What is a Hardwire Kit for a Dash Cam? [Deep Explanation]

Before we dwell into the simple steps of knowing further let us understand What is a Hardwire Kit for a Dash Cam?

What you should know about the hardwire kit is that it is a device that connects the dash to the car’s battery, and it is more of an easy fix as it removes the need for plugging into the lighter socket and gives a steady supply of power, as in it works on the basis that we can power our Dash Cam without using an actual power cord.

Pros & Cons of Dash Cam Hardwire Kit!

In this type of setup gives the benefit of getting all of this connected in a safer setup and all at once, as it has come along with a fuse, fuse holder, and fuse box making it all lie in one place and not being scattered out.

Going further let us understand the further 💡

setup that is the hardwire kit consists of all those things that are necessarily required for your automobile’s fuse box setup which carries setup like standard ATO or smaller ATM fuses. The interesting thing is that this kind of setup gives the benefit of having Dash Cam its very own power source, making it self-reliable as it removes the dependency on another outlet of power source that has the need to use a 12 V outlet, making the setup it very owns power source setup.

What brings us to worry is the need for the battery getting drain well what saves the day is that this hardwiring brings the benefit of fusing the Dash Cam into to car’s power control system making it not fall prey to battery-draining situations. What we should not be missing out on is that be it any car, that has park mode in their Dash Cam should not make the mistake of not having the hardwire kit, it is more of a necessity than a requirement.

How does a Dash Cam Hardwire Kit Work?

Let’s understand the whole setup step by step from the following before that’s what’s a hardwire kit.

The hardwire kit basically is a device that performs the function of a device which does the connection part of connecting two electronic components in a way that avoids the need for soldering what makes this setup very amicable is that it’s very efficient and cost-effective( if you don’t know-How Much Does It Cost to Install a Dashcam? ), making this very cool stuff, that does the connection part between components, as well as making it useful as it has the capacity to be used for end number of applications.

Do you know! How to Installing Dash Cam Without Wires | in 5 Minutes or Less!

Let us dwell deep into each part,

the wire connector comes with a male and female end cap making the two ends very definitive. When one end of the wire goes into the connector and vice versa, the setup is such that the device’s electrical component between each of their part is wired to connect and holds insulated caps on both ends making it the best way and easiest fix to setup the dash cam with the utmost ease with the hardwire kit setup.

The setup is easy as the installation is an easy part along with the fact that it works not as a temporary solution but more likely it is a permanent mark to the problem and can last too many years to use and come by.

We all get in ample number of worried incidents as when the wiring goes off in everyday scenarios, but when talking about this case the hardwire does wonders as it removes the worrying part in the cases of power cords getting cut off in the forms of damages induced or happened as a part of an accident, this brings us the use of these kits other kinds of scenarios or liabilities as such, in case of those we are in great use of these as security camera as well, making it total worthy and useful at any open scenario at hand. 

Be it any kind of products we use,

they all have a singular purpose, and many of those products have multiple or innumerable purposes, coming to the case of the Dash Cam the scenario serves the same as it has been providing innumerable purposes to an ample number of people and their uses to come by.

It is common to know the functionality that they serve is to do recording of driving which is not new, because it is what it’s known about mostly along with that it serves as a protectant part for liability issues mentioned above, and the part that it serves the use of being a security camera when you go into parking mode,

in the scenarios of leaving your car unattended leading to incidents of chaos if occurs any.  

Do you need a Hardwire Kit for a Dash Cam?

Going along its necessary to understand whether it is beneficial or not to use a hardwire kit for your Dash Cam.

Well, it is not always an essential kit to be used for your Dash Cam, as it is it is not a necessity that it serves to your Dash Cam, and what you should know as the reality is that there is a preference part to this rather than a necessity item.

The motorist is the top most one when it comes to the part of preference what makes these people favor some of the hardware kits is that part that the setup of neat cable management, as the hardwired is being done smoothly with zero error.

What is a kit without any additional features, cause additional features bring the impact to the table, and that comes with its specifications as different Dash cam comes with different specifications requirements.

💡Let us discuss with an example– to know the scenario better and clearly, one such Road Angel Dash camera; they are award-winning dash cam that has been hardwired that gives the opportunity to features and the benefit of extra features that make working easy as it enables the features of Parking Mode and Winter Mode that can be accessed and used for our full purposes. 

How Can I Hardwire a Dashcam?

The following steps give a complete look on how to hardwire kits as each is being manufactured under different manufacturer. 

Step 1 Decide on the positioning of your Dash Cam

The best to work this out is be at sitting at the driver’s seat and to get the position for our dash cam try out different positions in seat. For the ease of use keep at arm’s reach from your driving seat, in a way that you don’t find any kind of obstruction to your driving point of view with the position of the dash cam.

Step 2 Find the location of your vehicle’s fuse box 

As we are running from the power cable from the dash cam to the fuse box, the location of the fuse box to be found is of utmost importance. In case of any vehicle, the fuse box is underneath the dashboard of the driver’s or the passenger’s side. To know this better get your owner’s manual.

Step 3 Now start routing the power cable

Beginning from the dash Cam, lay out the cable in a way that it would run behind and lies hidden in the vehicle’s interior panels. This is done give an idea where to route the cable and what amount of slack to leave down to the fuse box and this is done by tucking the power cable into headliner. Now the next is to tuck the power cable along the side of the existing wires in the A-pillar. Later, route the power cable around the side and put it behind the interior panels leading to the fuse box. 

Step 4 – Find a fuse that’s “hot in start”

It is known that in general vehicles fuses have power at all the time, or in the case of the vehicle is in running way. So, to function the dash cam to start automatically when the vehicle is running mode and turn off the same way when the vehicle stops, a circuit kit needs to be connected to “hot in start” fuse, to test the hot fuse or identify which fuses are hot in start we use a simple circuit tester. 

Step 5 –Identify the ground point 

Note that the other end of the installation of your wiring kit should be grounded to your vehicle. To do this the lower panel should be removed to get an access to the ground point. Next is to remove the bolt and add the ground lug from installation kit.

Step 6- Time to Button up your install

By using a zip tie to bundle up the additional power wire together, now secure the wiring very safely to strong mounting point below the dashboard or behind the kick panel with the use of more zip ties to ease work.

Step 7- At the last, test your installation

Now, insert your key in the ignition and turn it on for the run position. If the installation is done as per the steps correctly, your dash cam starts recording. Later, reinstall all interior panels you’ve taken out for this in order to facilitate running the power cable.

Well, they are different methods and easy fix to installation methods that aids in powering your dash cam and one such is of the Hardwiring with a fuse tap cable. So, when you are following this installation technique, you will come across that this hard wiring technique is as requires the hardwire kits to perform and function itself well.

So, while understanding this fact we must talk about the ROVE Adapter Kit that comes with One Year Warranty and Lifetime Customer Support making it a wholesome product what you should know is that it consists of three leads with the needed hardwire connector for your devices that include miniUSB and PiggyBack Taps/Cables.

What Happens, If Your Dash Cam Is Not Hardwired for Parking Mode?

We can answer this as to a common question that in parking mode do the dash cam battery get drained.

Now we are dealing with the Nexar One dash Cam to clear this out, so if you are one who is curious about this question, we popped keep us in. This Nexar One Dash Cam comes with a kit that supplies uninterrupted power to your dash Cam, with this one it carries an OBD kit which is more of like a plug-and-play, or can be with a hardwiring kit, which is of the requirement to perform professional installation.

In this scenario what you should understand is that when your installation is done, when your Dash Cam moves in parking mode, and later during the hours of drives it gets charged, and in return it functions as such that this powers it back when in the required times of parking mode.

The setup works what way is that if you are someone who drives your car more than enough or more in whatsoever times(ex, jeep with best dashcam setup) or more often for a matter-of-fact what the fact is that when your car is in that parking mode there is not once chance of the battery getting drained.

Can Hardwiring a Dash Cam Affect the Car?

If you are with hardwiring your dash cam with a kit of three wires, the likely chances are that it split in three cases that is, one for constant power, one for car battery power and the third for ground.

This is case for using the kit with three wires as such. The scenario is more unlikely that this leads to draining of the battery in most case as such, as the power is constantly supplied to the camera in the cases of where car is parked in a parking area or a basement.

If you want you save yourself from this as such you have your choice, and that leads to VIOFO Dash cam that gives the user a choice of saving their battery’s power and reducing the effect on the car when put in the parking mode.

By use of such you have less likely effect on the car when hardwiring the Dash Cam.

What Fuse Should I Use for Dash Cam?

The suggestion is that to select a fuse slot that comes in the rating between 10A-30A as per the wiring requirement of your dash cam, this gives the enough power that makes it functioning properly with no faults and discrepancies. Who is your friend in this scenario is the vehicle owner’s manual this can guide you well as its helpful in avoiding fuse slots that could damage certain safety features of your vehicle so read thoroughly and proceed. The requirements you need for pertaining the safety of your vehicle is to find and purchase for the purpose of wiring the battery pack is 10A-20A.

FAQ

Is it a good idea to hardwire a dash cam?

It is always a great idea to give the provision of power to your dash cam as they prevent battery discharge and give the added benefit of capturing all the important moments in any instances of the car being parked or on the road.

Does the dash cam hardwire kit drain the battery?

If you are using the kit with three wires, it is more likely to drain the battery since it continuously powers the camera when the car is parked and switched off. 

Can you hardwire a dash cam yourself?

The easiest thing is hardwiring the dash cam, and all you require is that you need the hardwire kit, some fuse taps, and access to the interior fuse box for easy work setup. On average, you can take about 30 minutes to set it up

Author